LG-10 Explosion-Proof High-Efficiency Screw Vacuum Pump

Product Description1.SummaryThe dry screw vacuum pump is a rotor that uses a pair of parallel screws to make synchronous, high-speed and reverse rotation in the pump housing. The rotor and the inner wall of the pump body form a number of sealing spaces. During the rotation, the continuous transmission of gas is formed to achieve the purpose of suction and exhaust.The screw vacuum pump has a simple structure, but its processing technology requires higher requirements. It must ensure that the height between rotors is parallel, and that between rotors and between rotors and the inner wall of the pump body, there is a very small gap and no friction caused by contact, so as to ensure the realization of gas transmission and reduce gas backflow without the need for oil lubrication and sealing.This requires that the entire product must be the highest standard from material selection to processing. Because the clearance between components is required to be very small, it is necessary to ensure that the screw and pump body materials are not easy to deform, especially when the temperature changes to a certain value, the locking phenomenon cannot occur due to deformation. Special material treatment shall be selected to ensure the fine processing of all parts. In addition to the fine processing of the two screws, dynamic balance correction shall be carried out. The shaft end bearing must be a high-quality special bearing, which not only ensures the parallelism of the screw rotor and is not prone to slight displacement, but also ensures smooth rotation and is not affected by temperature and other factors. When the vacuum pump is working, the clearance between them is small without friction, the operation is stable, the vibration is small, the noise is low, the energy is saved, and the service life is extended. The special screw structure can continuously promote the air flow without compression. The exhaust port is lower than the screw position, the liquid discharge capacity is strong, and it is easy to clean. The pump cavity has short channels, no partitions, and the exhaust and discharge are smooth, so the working efficiency is high, the suction is super strong, and the limit vacuum degree of the pump is greatly improved, It can provide high vacuum ≤ 5Pa or even close to 1Pa; There is no lubrication and pollution in the working chamber, which can provide a clean vacuum without worrying about backflow pollution. Extracts can also be directly recycled or discharged without environmental pressure. Elaborate design, simple structure and precise processing make it more convenient to use and easier to maintain, which is favored by many industry users. It is widely used, not only to extract condensable gas, but also to extract gas containing a large amount of water vapor and a small amount of dust. The specially treated overflow surface can also be used to extract certain corrosive gas, and it is also a special product for oil and gas recovery, solvent recovery, special gas recovery and other industries.2.Advantages and disadvantages of dry screw vacuum pumpA.Advantage    I. Clean and environment-friendly, the working chamber is free of lubricating oil, which is conducive to medium recovery, can obtain clean vacuum, no oil consumption, waste water discharge, and no pollution to the environment.   II.The vacuum degree is high, the limit vacuum degree is ≤ 1Pa, and the pumping capacity in the high vacuum area is large.  III.The anti-corrosion design is optional. The flow passage parts are made of titanium, stainless steel, nano ceramics, spraying NIP alloy and other materials and anti-corrosion coatings.  IV.The condensable gas and a small amount of dust gas can be removed, and an automatic purging device is designed.   v.Special shaft seal design prevents mutual pollution between pumped medium and lubricating oil.  vi.Variable pitch screw pump saves energy and has low noise.  vii.The operation is stable, the rotor is subject to fine dynamic balance test, and the operation vibration is small.  viii.High configuration, sealed in Germany, Internationally renowned brand of bearing position, gear grade 5 grinding.B.Shortcomingi.Due to the difficulty in processing the screw pump, the screw pump used in China mainly depends on imports, and the price is very expensive.ii.It is not suitable for pumping out explosive gas.iii.It is not suitable for pumping gas with too high oxygen content.LG-10 Screw pump has high efficiency, high vacuum and high cleanliness, and has attracted much attention from users. It is a small vacuum pump that cools down in the form of air cooling.There is no medium in the working chamber, which can obtain a clean vacuum.. No clearance between rotating parts, high speed operation, small overall volume.There is no compression in the gas, suitable for extraction of coagulable gas.Can remove a lot of steam and a small amount of dust gas occasions.. High vacuum, the ultimate vacuum up to 1 Pa.Screw material is high st