Wood Design Spc WPC PVC Floor Tile Vinyl Flooring

Product DescriptionLuxury Vinyl Tile, PVC FlooringProduct: LVT (Loose Lay, Dry Back, LVT Click), SPC Click , WPC ClickColor: Wood Design/Stone DesignPackage: PalletizedMOQ : 1000m²/ColorPayment Terms: 30% T/T deposit. 70% T/T against copy of B/L or LC at sightLead Time: 30~45 days(1)    LVT Dry BackSize: 6''x36'', 9''x48'', 12''x24'', 18''x18'', etc.Thickness: 2mm, 2.5mm, 3mm Wearlayer: 0.1mm~0.7mm(2)    LVT Loose Lay(Anti-slip Backing, Sticky Backing)    Size: 18''x36'', 9''x48'', 18''x18'', etc.    Thickness: 4mm, 5mm    Wearlayer: 0.3mm~0.7mm(3)    LVT Click    Size: 180x1210mm,220x1210mm,304.8x609.6mm, etc.    Thickness: 4mm, 4.5mm, 5mm    Wearlayer: 0.3mm~0.5mm    Available for length 1.5m/1.8m (4)    SPC Click    Size: 172x1210mm, 218x1210mm, 300x600mm, etc.    Thickness: 4mm, 4.5mm, 5mm    Wearlayer: 0.15mm~0.5mm    Available for length 1.5m/1.8m    Specially for Residential Use (5)    WPC Click    Size: 180x1210mm, 220x1210mm etc.    Thickness: 5.5mm, 6mm, 6.5mm, 7mm    Wearlayer: 0.3mm~0.5mm    Available for length 1.5m/1.8mDetailed Photos CertificationsCE, ASTM, Floorscore, ISO9001, BSCI......Packaging & ShippingInstallation InstructionsLaying instructions- CLICK SYSTEM      General:Then execution of floor-covering work is construction work within the terms of the German Construction Contract Procedures (VOB). The VOB Part C DIN 18365 "Flooring Work" thus provides the basis for the execution of flooring work and the laying of flooring.Before choosing the appropriate floor covering it is always necessary to know the on-site type of use and existing sub-floor in order to select the right and proper flooring. Only in this way can added value and value maintenance throughout the planned lifetime of the floor covering be guaranteed.Sub-floor:The sub-floor must be even, clean, sufficiently dry, free of dust and cracks, and sufficiently load-bearing. It is always necessary to prime mineral sub-floors so that no dust is present on the existing sub-floor. Before carrying out the flooring work an evaluation of the sub-floor in accordance with DIN 18365 "Flooring Work" is necessary. As design flooring are vapor-proof coverings, residual moisture in the sub-floor is particularly significant. It is to be demonstrated that appropriate measurements have been taken. With existing underfloor heating there should be an appropriate heating protocol to ensure the sub-floor is ready for the installation of the flooring.Installation:•Checking the floor coveringOur CLICK-design flooring undergo a strict quality control procedure that guarantees high-quality standards. If, contrary to all expectations, material problems should be identified on site, there are to be notified before cutting to size and laying. Claims for obvious defects (e.g. Color variations, differences in thickness, surface defects, insufficient accuracy of fit etc.) cannot be accepted after laying.If a number of packages of design flooring are being used the contents should be checked for batch-to-batch variation before cutting and laying. When ordering it is imperative that reference be made the need for a consistent color-matched delivery with no batch variation.•Interior climatic conditionsThe floor covering must be adapt to the room temperature before laying. This requires at least 24 hours acclimation. For installation the room air temperature must not be less than 18ºC and temperature of the sub-floor not less than 15ºC. The relative humidity should not exceed 75%. With underfloor heating floor temperatures of between 18ºC and 22ºC are o be observed.In the winter months the underfloor heating should be kept at a low temperature for at least 72 hours before the floor covering is laid, during laying, and for at least hours after laying (see surface temperatures). Rapid or distinct changes in temperature can cause gaps or warping in the flooring.These climatic conditions are to be maintained for at least 48 hours before laying the flooring, during installation, and also for at least 72 hours after the flooring has been completed. Larger changes in room temperature are to be undertaken gradually in accordance with the usual room climate conditions.•Laying the floor coveringPriming is always recommended on mineral sub-floor in order to bind dust and particle matter and thus to prevent noise being generated when the flooring is in use..Before laying the CLICK-design flooring the room is to be measured and assessed in terms of laying direction and starting point.We recommend the use of our Click-Underlay, which not only has a noise-mitigating and heat-insulating effect but also compensates for slight sub-floor irregularities and impurities without adverse consequences.The use of Click-Underlay is imperative with the following sub-floors: parquet, laminate, ceramic tiles (with joints of max. 5mm width and 2mm depth), PVC-flooring and flat stone floors. The "sticky" surface significantly reduces vertical movement to the sub-floor. The underlay is used tra