High Quality and Cheap Tdp-1.5 Milk Tablet Press Machine Small Tablet Machine Manual Single Punch Powder Tablet Pressing Machine Candy Pressing Machine with CE

Product DescriptionTDP SINGLE TABLET PRESS MACHINETDP-1.5 single punch tablet press machine ,which could press the power material to tablet ,could be widely used in the pharmacy factory ,chemistry factory ,hospital and R & D bureau. This machine is with good performance ,strong suitability ,simple operation ,easily repair ,small cubage ,light .Even under the conditions or power cut ,hand swing is available .Compare to original TDP model press machine ,it is enlarged the machine intensive and engine power with bigger strength .In the meantime enlarge the filling depth ,hence to expand the specification range of tablet .Therefore this machine can meet the demand of different kinds of Chinese traditional medicine and Western medicine and other similar product's requirement .It's deeply welcomed by our customers in different field.  Product ParametersMain Technical Data:        No.ItemTDP-1.5TDP-5TDP-61Max .press strength(KN)1550602Max .tablet diameter(mm)1220253Max .filling depth(mm)1218164Productive capacity(Pcs/Hour)4700450040005Motor power(kw)0.250.551.16Turning speed(r/min)1400140014007 Weight (kg)651251508Length*Width*Height(mm)570x380x630650x440x650700x500x900 1.pedestal     2. adjust gear   3.butterfly shape nut     4. lift fork     5. empaistic bolt 6. bedplate    7. baffle for power 8. bucket feeder 9.upper rush   10. .Up rush rod 11.feeder rod  12.flywheel    13. feeder wheel  14. eccentricity wheel   15.oil cup(6 gM10)16. principal axis  17.belt cover  18.big gear  19. little gear (go through axis)  20. lift pole 21.V-belt     22. motor  23. down rush central rod.          Installment and connection of the press machinePress-tablet machine should be installed on the wood worktable (as well on the cement table). Use 4 units of M12 bolts to fix it .The high from the worktablesurface to ground is around 600mm(consider easily to the operation) . Toconvenient to disassembly and repair., there should be a hole the diameter around 35mm counter to the bottom of pressure rod.To insure the safety ,connecting ground wire before connecting the power ,and Then remove the triangle belt ,to rolling direction of the operation .(The rotary Direction should be opposed to the arrow direction on the shield or hand wheel.)If the rotary direction were incorrect ,it would connect the line additionally ,and The install the triangle belt.IV, Assemble and unassembled of the die and adjustment during the operationAssemble of the dieAssemble the down rushUnscrew the fixed bolt ,turn the hand wheel to raise the central rod to the top location and insert the undershoot rod to the hole of the down central rod.(Attention the gap level the gap level aim at the bottom tighten bolt) At last screw the down rush fixed bolt.Assemble up rushUnscrew the fixed bolt ,turn the to up rush rod to the upper hole ,use spanner to lock the upper bolt and screw the fixed bolt.1.Fix the intermediate mould Unscrew the fixed bolt ,and put the mould into the hole of mould plate ,in the Meantime insert the rod into the hole .Push it to the bottom of the hole and then Screw the bolt .level the intermediate mould and avoid locking in the plate to damage the orifice.2.Turn the hand wheel ,let up rush rod slowly drop to orifice .and observe whether there is collision or friction ,and then unscrew the fixed bolts (2) of the fixed plate ,adjust the fixed location of the intermediate mould plate .Let the up rush rod into the orifice of intermediate mould ,and the adjust it till no collision or no friction it can be called qualified installment..3.The adjustment of the tablet outTurn the hand wheel to raise the down rush rod to the top point ,observe whether the surface of down rush rod and intermediate mould are on the same level ,if No. unscrew bolt and press plate of gear ,make the surface of down rush rod and intermediate .Next step ,turn hand wheel and make the empty machine run for several circle .If it goes well ,and then you can press some material to try press and continue to adjustment for next step.4.Adjustment of filling depth (that's the adjustment for the weight of tablet) .Unscrew the bolt and loose the gear press plate ,left turning the down adjustable gear to raise the down rush rod ,that's reduce the filling depth (lessen the weight of tablet). After adjustment should to install the gear press plate and screw bolt.5.Pressure adjustment (That's adjustment of hardness of tablet).Loosen the locked nut and turn up rush rod ,left turning rush rod to move down and then pressure increased ,the hardness of the tablet would be increased .On the contrary ,right turning would decrease the pressure and lower the hardness of the tablet .After adjustment use the spanner to lock the bottom of the up rush and screw the nut..Till now ,the adjustment of the die is basically completed ,restart the machine for trial press several tablets to check the weight of the tablet ,hardness and surface etc quality issues .if it's qualified ,you can put into production .Du