5-12 mm Reinforcing Mesh Welding Machine with CE Certificate and ISO

Product Description5-12 mm Reinforcing Mesh Welding Machine This Machine is mainly used to produce steel wire diameter 5.0-12.0mm,material round steel wires and ribbed steel wires,mesh size:100*100-300*300mm reinforcing mesh panels. Detailed PhotosLine Wires Aligning and Automatic Feeding DeviceThe Line Wires Automatic Feeding Device is to automatically send the manually threaded line wires to the welding electrode position of the main mesh welding machine, so as to facilitate the main mesh welding machine to complete the welding process. When the line wires feeding car is automatically feeding, the next group of line wires will be manually prepared, which can realize the production of the main mesh welding machine without shutdown and greatly improve the production efficiency.a)It is composed of a line wires feeding car, an alignment device, front and rear wire rollers and the feeding car frame.b)There are 16-26pcs line wire clamping devices, which are installed on the beam of the line wires feeding car, and the clamping action is realized by the air cylinder.c)The line wires alignment positioning device moves up and down. Before manual threading line wires, the alignment and positioning device is lifted to ensure that the length of all the line wires is consistent.Cross Wire Automatic Falling Hopper The device is a kind of feeding device which can send the pre-cut steel wires into the welding electrode position of mesh welding machine according to the welding requirements,can store about 1 tons of pre-cut cross wires, greatly reducing the intensity of frequent feeding;a)This hopper is composed of a platform,two ladders, a falling hopper, they are all installed on the pulling mesh rack backward and forward.b)There is a ladder on both sides of the platform for easy operation.c)The falling hopper uses a disc-shaped groove wheel to accurately pick out the wire. According to the welding requirements, each transverse cross steel wires is evenly fed into the position of the pusher one by one. The wire falling wire power is 13.5 N. M step motor.d)A set of cross steel wires positioning clapper is installed at the pushing position of pusher in the down beam of the mesh welding machine to ensure the consistency of the cross steel wires. The clapping power is a three axis cylinder with a cylinder diameter of 40mm.  The up and down electrodes all adopts special CuCrZr,the electricity conductivity,hardness and wear resistance are all very good,the changeover time of the longitudinal cell is reduced to about 30 seconds.Welding electrodes are driven by the spindle passing through the crank,and installed with adjustable spring pressure,This structure is not affected by climate and convenient maintenance and usage.And the up and down electrodes both adopt water cooling system,thus an reduce the heat of the upper and lower electrodes when the machine works, and can work for 24 hours continuously.  Pulling Mesh Device It is to pull the welded cross wires out of the mesh according to the parameters set by the program, and according to the length of the mesh, it can realize multiple reciprocating pulling mesh, until the whole mesh is completely pulled out.It is composed of four parts: the bottom frame, the movable pulling mesh frame, the pulling mesh car and the supporting mesh tubes.   Product ParametersFully Automatic CNC Reinforcing Mesh Welding Machine Main Technical Parameters :Item WZ-2000AWZ-2500AWZ-3000AWZ-3300ANumber of Electrodes20243032Max.Mesh Width2500mm2500mm3000mm3300mmWire Diameter5.0-12.0mm5.0-12.0mm5.0-12.0mm5.0-12.0mmMesh Length3-12m3-12m3-12m3-12mCross Wire Space100-300mm100-300mm100-300mm100-300mmLine Wire Space100-300mm100-300mm100-300mm100-300mmElectric Capacity200KVA*10200KVA*12200KVA*15200KVA*16Welding Speed40-60t/min40-60t/min40-60t/min40-60t/minControl SystemPLC control and Touch ScreenCertifications Installation InstructionsCompany ProfileAnping Wanzhong Wire Mesh Products Company entered the wire mesh industry in 2006, specializing in the manufacturing of various types of Fence Mesh Welding Machines, Reinforced Mesh Welding Machines, Automatic Construction Mesh Welding Machines, Breeding Mesh Welding Machines, Chain Link Fence Machines,Cattle Fence Machine, Nail Making Machines, Wire Drawing Machines, Barbed Wire Machines, Razor Barbed Wire Machines,Wire Straightening and Cutting Machine,etc.Wanzhong Company has its own professional R&D team,customized design and production can be carried out according to the special requirements of customers,and has already won fifteen national patents until January 31,2022. It has successfully passed ISO9001-2008,CE certification and SGS certification,and it is recognized as a national high-tech enterprise by our government,and our company credit rating is "AAA".Our machines have already exported to more than 40 countries, including USA,Russia,Algeria,Malaysia,the United Arab Emirates, Kuwait, Yemen, Oman, India, Uzbekistan, Kazakhstan, Iraq, Mexico, Tunisia, Ken