Waste Tyre Rubber Plastic Pyrolysis to Diesel Oil Gasoline Equipment

Waste Tyre Pyrolysis PlantBatch Type Waste Tyre Pyrolysis PlantPerformance FeatureWhole tyre feed,no need to break, which reduces cost.Adopt multilevel cooling circulation to get more fuel oil.Discharge process through pulse dust removal processing,no dust emissions.Easy operation,high efficiency and 2-3 people to operate.Plant adopts fully automatic submerged arc welding process,through x-ray detection,        to improve the security of plant.Technological ProcessTyre transported to reactor by conveyor to pyrolyze.Oil and gas from pyrolysis go into gas-liquid separating tower and separate, and enter into condenser to liquify , to get fuel oil, then enter into oil storage tank.Coarse carbon black and steel wire from pyrolysis are output by automatic slag remover, transported to carbon black processing system by cooling hoist. Separate steel wire and carbon black through the magnetic separator,to get  industrial carbon black and steel wire.Steel wire pulled out by winch,compressed into pieces,and do steel scrap process.Flammable gas enter into waste gas tank and processed. Then extracted by vacuum pump, enter into water sealed tank and send to hot air furnace to burn.Main Performance ParameterItemTypeXFLJ--10XFLJ--20Capacity/ 24h10T20TWorking temp.≤650°FuelFuel oil, Natural gas, Liquefied gasHeating wayCirculating hot air heatingTyre request≤1200 mmWorking pressureNormal pressureFlame retardant waySteam blowFuel consumption200 kg400 kgSize7300 × 2400 × 3100(mm)7300 × 2400 × 3100(mm) × 2Total power65 kw120 kwPower Consumption 30 kw/h60 kw/hFloor space25000 mm × 5500 mm25000 mm × 11500 mmHighest point of installation5000 mm5000 mmRemark:This parameter is just for reference.Size change caused by design improvement will not inform customers specially.Please refer to documents enclosed with products.Product Recovery Rate  1. Oil: 40-45%2. Carbon black: 32-36%3. Steel wire: 14-16%4. Syn gas: 5-8%Semi Continuous Waste Tyre Pyrolysis PlantPerformance FeatureIntegral design, no need to precast foundation, quick and easy installation.Airtight high temperature material feed, saving heating time and reduce the temperature loss.Adopt multilevel cooling design to get more fuel oil.Hot air heating, unique heat cycle design, heated more evenly, reducing the operating cost.Airtight high temperature slag, no dust, clean and environmentally friendly.Technological Process1.Broken tyre transported to feeder firstly by conveyor, then to reactor. 2. Oil and gas from pyrolysis go into gas-liquid separating tower and separate, and enter into condenser to liquify , to get fuel oil, then enter into oil storage tank.3. Coarse carbon black and steel wire from pyrolysis are output by automatic slag remover, transported to carbon black processing system by cooling hoist. Separate steel wire and carbon black through the magnetic separator,to get  industrial carbon black and steel wire. 4. Shatter carbon black, to get industrial carbon black after deeply processing. Steel wire compressed into a piece of scrap processing.5. Flammable gas enter into waste gas process tank to desulfur. Then extracted by vacuum pump, enter into water sealed tank and send to hot air furnace to burn.Main Performance Parameter  ItemTypeXFLJ--8XFLJ--16Capacity /24h8T16TOperating temperature≤650°FuelFuel oil, natural gas, liquefied petroleum gasHeating wayHot air circulation heatingTire requirementBlock tyre ≤5mmWorking pressureNormal pressureMethods of flame retardantSteam blowFuel consumption200 kg400 kgBoundary dimension7300 × 2400 × 3100(mm)7300 × 2400 × 3100(mm) × 2Total power85 kw160 kwPower consumption 40 kw/h75 kw/hFloor space25000 mm × 5500 mm25000 mm × 11500 mmHighest point of installation5000 mm5000 mmRemark: This parameter is just for reference. Size change caused by design improvement will not inform customers specially. Please refer to documents enclosed with products. Product Recovery Rate 1. Oil: 40-45%2. Carbon black: 32-36%3. Steel wire: 14-16%4. Syn gas: 5-8%Fully Continuous Waste Tyre Pyrolysis PlantPerformance FeatureInternal screw rotatory pyrolysis. No coking.Hot melt processing in advance, process generated HCL specially, more environmental protection.Adopt multilevel cooling design, to get more fuel oil.Hot air heat, cooperated with low temperature pyrolysis catalyst, extend working life of plant. Enclosed production all the way, no leakage and no dust loss, environmental protection. Exhaust gas multistage processed, gas discharge reach European Standard level.  Technological ProcessWaste tyre and medical waste sent into fuel preheater by conveyor to melt. Process generated HCL specially.  Melted fuel continuously sent into reactor, and finish pyrolysis under low pressured catalyst. After generated gas during pyrolysis separates in gas-liquid separator, liquify in condenser and get fuel oil. After fixed bed second catalyst and dewaxing , can get the fuel oil with high quality. Carbon residue after pyrolysis output continuously by cooling con