O-Rings Seal Rings and Gaskets Rubber Vacuum Vulcanizing Press

--Brief introduction of Hydraulic Hot Press Rubber Wrist Band Logo Rubber O Ring Moulding Machine Product features:The BF-R1 series tablet machine has the characteristics of simple structure, high pressure, high efficiency and wide applicability.Product description and usage:BF-R1 series flatbed machine is mainly suitable for vulcanization molding of various common flat rubber molded products. Suitable for the production of various rubber products, silicone products, seals, O-rings, oil seals, auto parts, rubber shock pads, keyboards, medical rubber parts, electrical insulation parts and other rubber products and bakelite products, handicrafts, etc. It can also be used for compression molding of other thermosetting plastics, foam products, foam resins, bakelite, thin metals, building materials and other models.Three, structural characteristics:3.1 This machine is guided by four columns, and the main machine table is composed of upper plate (also called upper beam), lower frame, movable plate (moving platform), cylinder group and upright column. The oil cylinder is a plunger structure and is installed in the lower base. Two fast oil cylinders are installed on both sides of the lower base.3.2. The equipment has an independent power mechanism and electrical system. The electrical box is fastened to the right side of the host. It uses a PLC programmable controller and is equipped with an LCD display. The buttons are centrally controlled and easy to operate. The working pressure and heating temperature can be adjusted within a certain range. This model has two working modes: manual and semi-automatic.3.3. This machine has a single-machine single-pump station structure, and can also be manufactured with dual or multiple machines according to user needs. The oil pump is located on the right side of the main engine, and the lower frame doubles as an oil tank;3.4. When the machine is working, the plunger moves from bottom to top to close the mold, press to form, and has the functions of automatic heat preservation, pressure holding and exhaust to ensure product quality.Four, function introduction: 4.1. With automatic pressure compensation function, in the rubber product compression process, the pressure drop caused by the flow of raw materials can be automatically compensated. 4.2. Automatic exhaust time, exhaust times, secondary exhaust, up and down residence time, heating temperature, vulcanization time, and mold clamping pressure can be set during the exhaust process, which is easy to operate. Vulcanization countdown display function, early warning function for the end of vulcanization, and automatic mold opening. 4.3, Fast opening and closing of the mold, high production efficiency, slow locking and pressure, to protect the mold.4.4. When the product is vulcanized and formed, the oil pump motor stops working, which saves electricity.4.5. Using segmented heating tubes, the hot plate has high temperature control accuracy and energy saving.4.6. Reasonable oil circuit configuration, saving energy consumption, using imported valves, safer and more reliable to use.4.7. The hydraulic cylinder adopts German imported technology, and the seal adopts Japanese original imported NOK, which is reliable in sealing and long in life.4.8, The design is reasonable, the operation is simple and easy to understand, and the maintenance is convenient.4.9, single-layer and multi-layer options are available.Main technical parameters of the equipment:PNominal clamping force 0.50MN 50tFlat plate (hot plate) specification 400x400x thickness 60mm MaterialQ235 high quality carbon structure steelNumber of working layers 1 layerNumber of hot plates2 piecesHot plate spacing250mmParallelism of hot plate≤0,09mmThe surface roughness of the hot plateRa≤2.5 μmHeating methodElectric heatingThe heating power of each heating plateis 500w*6=3kwHeating temperature200°CTemperature control methodTemperature control meterMotor power2.2KWPressure per square centimeter32kg/cm2Plunger stroke/diameter 250mm /∮200mmMaterialQT500-7Number of cylinders1 set Material: QT500-7Use system pressure16MpaStructurefour-post typeNumber of columns/diameter 4 pieces / ∮50mm45# steelControl modemanual control manual control valveWeight about 1300KgMain performance characteristics1. The oil cylinder adopts advanced sealing structure, reasonable design and reliable performance.2. With automatic control of mold clamping, manual exhaust, automatic pressure compensation, vulcanization timing, time alarm, manual controlControl down the function.3. Description of the main components of the host3.1. Column: The column is made of high-quality 45# steel. After quenching and tempering, the strength and tensile force of the column are improved, and it is not easy to deform and break.3.2 Plunger: The material of the cylinder is QT500-7, the cylinder diameter is Φ200mm, and the quantity is 1 piece.3.3. The materials of upper and lower base and platform are all QT500-7.3.4. Hot plate: The hot