Hq Core Barrel System Head Assembly Accessories Drilling Tools Mining Geological

Product DescriptionDrilling tool assembly (P, H, N and B)Relevant description of products:Retrieve the inner tube with an overshot without lifting out the whole rods string to obtain the core, the wireline coring system lifts the underground core sample out of the borehole through the overshot to take back the entire inner tube and conduct sampling analysis. This improves productivity of the work site and guarantees safety of core sample during drilling down.The system is realized through a fully independent inner tube. During its working, the inner tube does not connect with the overshot but locates at the bottom of the coring drilling rod directly (behind the coring drilling bit). An assembly device is installed on top of the inner tube, which includes coring and recycling functions. When the inner tube is full of core sample, the overshot is placed to the bottom from the borehole through a steel wire rope and lifted out by a winch. After the inner tube assembly is lifted to the surface, an empty inner tube is placed to the bottom of the hole to recover the drilling. This improves well drilling efficiency.Our company provides core barrel assmeblies of different diameters to meet customers' demands. The wireline coring system is applicable for most drilling conditions and standard DCDMA hole sizes (B, N, H and P).Currently, the company provides two models of wireline coring systems: double-tube and triple-tubeCore barrel assembly: It consists of inner tube and outer tube groups.The inner part consists of the following parts: spearhead assemly, retrival components, core sample collection component, landing shoulder, stop ring and other parts.inner tube group, independent from outer tube group, collects core sample sample during well drilling.The outer tube part consists of parts , which includes locking coupling, adapter coupling, outer tube, etc. The outer tube group that is kept at the bottom of the hole all the time holds the inner tube assembly during drilling.The triple tube coring system AU3 has the same components as the dual-tube. And its interior has a third tube that is known as liner tube of the inner tube.Liner tube of the inner tube is placed in the inner tube. The triple tube system can realize overall recovery ratio of core sample when drilling stratum with coal, clay or bigger crack. The liner tube or split tube keeps the core sample at its receiving status to collect or load and store easily.Only N, H and P sizes are available for the triple tube coring system.Detailed Photos1 Spearhead Point2 Detent Plunger3 Compression Spring4 Spirol Pin5 Spearhead Base6 Latch Retracting Case7 Spirol Pin8 Nyloc Bolt9 Washer10 Latch Compression Spring    11 Upper Latch Body12 Latch13 Link14 Spirol Pin15 Stainless Steel Ball16 Landing Indicator Bushing17 Shut-off Valve18 Pump-in Lip Seal19 Spindle Bushing20 Landing Shoulder21 Lower Latch Body22 Hex Nut23 Spindle24 Shut-Off Valve,Hard25 Valve Adjusting Washer26 Thrust/Hanger Bearing27 Spindle Bearing28 Compression Spring29 Stover Lock Nut30 Inner Tube Cap31 Grease Fitting32 Stainless Steel Ball33 Check Valve BodyPackaging & Shipping CertificationsOur Workshop     We have successively put into operation the international advanced intelligent production lines,it has two intelligent production lines with an annual output of more than 150,000 drill rods. In the future,there will be 8 intelligent production lines in the second and third phases with an annual output of more than 600,000 drill rods.     Our core productivity is supported by America Inductotherm heat treatment equipment and MAZAK CNC machine tools,Siemens control system.We will achieve our goal of the overall production intelligence in our factory in next 3 years which will be the standard equipment of Au-prospect.  Our Exhibition & Our PartnersFAQQ1. Where is your factory?A1: Our factory is located in Wuxi, Jiangsu, China, it takes only about 2 hours driving from Shanghai.Q2. How do you control quality?A2: ISO9001 has been passed. Mill Test Certificate is supplied , meanwhile the Third Party Inspection is available according to customers' requirement.Q3. What are the advantages of your company?A3: Our core productivity is supported by American Inductotherm heat treatment equipment, MAZAK CNC machine tools, and Siemens control system.Q4. Can you arrange the shipment?A4: Yes, of course, we have our forwarders which has cooperated with us for years.Q5. How about the delivery time?A5: It will be decided by the orders. Normally within 3 days after receiving your advance payment if we have stock.Q6. Can you provide sample?A6: Small samples in store can be provided for free./* March 10, 2023 17:59:20 */!function(){function s(e,r){var a,o={};try{e&&e.split(",").forEach(function(e,t){e&&(a=e.match(/(.*?):(.*)$/))&&1