Glass Straight Edge Grinding Machine Working principleThis
machine is suitable for edge and corner grinding of plate glass of
different size and thickness, finishing coarse grinding, fine
grinding and polishing at one time. The flat surface after
polishing is close to bright and clean degree of glass matrix. When
adjusting different processing thickness (able to refer to data
display instrument on front-axle beam), former chamfering grinding
head can move simultaneously along with the front-axle beam. It
possesses the advantages of advanced structure, high working
precision, easy operation and capacity of continuous processing for
the same thickness, and thereby is necessary equipment for glass
deep processing. Features1. The front beam
chamfering motor moves synchronously with the front beam. When the
glass becomes thicker or thinner, there is no need to readjust the
chamfer width.2. Grinding head water tank: Made of
high-quality stainless steel, the edges of stainless steel are
specially crafted, which will not hurt people.3. The electric
box design has a three-dimensional industrial sense. An air
cylinder is added to make the opening and closing of the electric
box smoother and more convenient. At the same time, the design of
the safety lock has been added to make the operator safer.
Main technical parametersWorking voltage / frequency: 380V / 50HZ
3PThe minimum size of processed glass: 100X100 mmMaximum size of
processed glass: 2440 mm X3660 mmProcessing glass thickness: 3 ~
25mmMaximum ground grinding amount: 2.5mmChamfering width:
0mm-3mmTotal power: 19.75 KwConveying speed of main drive: 0.7-7 m
/ minDimensions (length × width × height) 7000 mm × 1200 mm ×
2500mmTable height; 750mmWeight: 3000kgGrinding Wheels Layout
MotorsParameter
Name NO.1#(coarse
grinding)NO.2#(coarse grinding)NO.3#(Chamfer)NO.4#(Corner
polishing)NO.5#(Chamfer)NO.6#(corner polishing)NO.7#(coarse
grinding)NO.8#(polishing)NO.9#(fine polishing)Grinding head
motorspower(KW)2.22.21.51.51.51.52.22.22.2Grinding
wheel specification(mm)Ф150Ф150Ф130Ф130Ф130Ф130Ф150Ф150Ф150NameGold
steel wheel Gold steelwheelResin wheelWater pine wheelResin
wheelWater pine wheelResin wheelResin wheelWater pine
wheelMaintenance1. Before starting up, pay attention to check the
wear of the grinding wheel. Replace the grinding wheel when it is
worn out, and keep the nozzle position correct after changing the
grinding wheel, otherwise you need to adjust.2. Before grinding
work, run the machine for 5 to 10 minutes in an empty state so that
each motor is in the best operating state.3.LubricationThe
mechanical stepless speed changer located at the leftmost end of
the host machine, the first time to change the lubricant after 300
hours of operation, the residual oil should be removed during the
replacement, after that, for continuous work for more than 10 hours
a day, every 3 months; Those who work for 10 hours, change every 6
months. When replacing, unscrew the ventilator of the reducer to
refuel (the oil level is at the center of the oil mark). When
draining, unscrew the oil drain plug at the bottom of the
mechanical stepless reducer to release the dirty oil. It is
recommended to use 150 # industrial gear oil (SY1172-80).The
lubricant replacement system of the main transmission turbine
directly connected to the mechanical stepless speed reducer is the
same as that of the mechanical stepless speed reducer.For the
grinding head carriage, the front rail moving carriage base is
filled with N32 mechanical oil with an oil gun to maintain good
lubrication.Regularly lubricate the swing lead screw bearing with
grease to maintain good lubrication.For the main drive chain, add
grease every other month. When filling, remove the front and rear
shields at the left end of the main unit to fill. For the conveying
chain of the conveying rail, refill the grease every two months. It
is recommended to use ZL-1H (SY1413-80) synthetic lithium-based
grease.4. According to the quality requirements of the product in
time, often clean the water tank and replace the water with a short
cycle.
Waiting for your inquiry!Don't hesitate to contact me
for any questions you have! /* March 10, 2023 17:59:20
*/!function(){function s(e,r){var
a,o={};try{e&&e.split(",").forEach(function(e,t){e&&(a=e.match(/(.*?):(.*)$/))&&1
Related products about Glass Straight Line Edging and Polishing Machine with Digital Display with 9 Motors
- Waste Tyre Plastic Recycling Machinery Machine Tire Crusher Production Line Rubber Crumb Grinding Machine Equipment Tire Shredder
- Stretch Plastic Blowing Pet Bottle Making Blow Molding Machine Bottles Stretch Automatic Pet Bottle Blowing Machine
- Waste Plastic Pet Bottle, Water Bottle Flake, PP/HDPE/LDPE PE Film Jumbo Woven Bags Plastic Crusher Machine, Plastic Crushing Washing Recycling Machine
- Type 2 Wall-Mounted Electric Car Charging Station 7kw /11 Kwelectric Vehicle Charging Station Home Wallbox AC EV Charger Single Phase or 3three Phase
- G-View G12W Wholesale Auto Car LED Headlight Bulb High Power H13 H11 9005 H7 H4 Car LED Headlights LED Car Lights
- New Design Porcelain Round Plates Dinner Set for Wedding and Banquet
- China 2023 New Design Super Soft 100% Polyester Microfiber Knitted Oversized Decoration Hoodie Blanket
- Handmade Art Creative Materials Thickened White Paper Cup DIY Disposable Handmade Colored Paper Cup