Automatic Printing Slotting Die Cutting Machine

4 Colors Carton Printing Slotting Die Cutting Machine with StackerDetailed configuration and technical parametersMachine performance• Computer control can store common orders, change orders faster and operate more conveniently.• All drive rolls are made of high quality steel, hard chrome plated, and grinding.• Oil automatic balancing device keeps the oil in each unit at the same level.1.paper feeding unit (one group)(1) Sun wheel box leading edge paper feeding system.A.  Four-axis leading edge paper feeding, increase fan flow, and maintain accurate speed when feeding at high speed and low speed.B. Adjust the airflow and pressure in 4 steps to match the cardboard size.C. Positioning from the front to reduce paper feed errors and improve the accuracy of paper feeding, printing and slotting.D. Electric control of left and right side baffles, computer adjustment.E. Rear pallet holder electric control front and back.F. Manual adjustment of the front stop cardboard gap.G. Paper can be fed continuously or separately. (Continuous or separate sheets can be selected as needed).H. Paper feed counter, set, display the production quantity.(2) paper feeding upper and lower rollersA. upper roll; outer diameter of 155mm, steel pipe surface wrapped wear-resistant rubber, balance correctionB. Lower roll: The outer diameter is 155mm. The surface of the paper feed roller is embossed and hardened.C. Feeding pressure roller adjustment gap is adjusted by self-locking structure, the adjustment range is 0-12mm.D. The power transmission of the pressure roller adopts the rolling cross coupling transmission to reduce the wear and make the transmission more balanced.(3) machine clutch, automatic return zero deviceA. The drive shaft is equipped with a friction clutch to avoid malfunction and damage the machine.B. Main engine start protection device (when the machine is not locked, the main unit cannot start running).C. Paper feeding unit, printing unit and slotting unit are electrically and automatically reset to zero.D. The general carton uses the automatic zeroing device. It can be adjusted to the correct position by printing 1 or 2 sheets of paperboard to reduce the waste of cardboard.5. Dust removal device, the printing plate can not stick to impurities during printing to reduce the number of plate wiping.6. The special leading edge device does not destroy the strength of the cardboard.2. Printing unit(1) printing rollerA. The outer diameter is 395.6mm.B. is made of high quality steel with surface grinding and hard chrome plating.C. Balance correction, smooth operation.D. Reel hanging version, using the left and right locking devices to make the hanging version more accurate.E. full version of the hanging groove, suitable for 10mm hanging strips.F. Loading and unloading the printing plate, the electric control of the foot switch Positive reverse.(2) Printing pressure rollerA. outer diameter is 176mmB. The surface of the steel pipe is ground and hard chrome plated.C. Dynamic balance correction, smooth operation.D. Pressure roller gap adjustment adopts self-locking structure adjustment, the adjustment range is 0-12mm.(3) Metal anilox roller (three group)220 mesh two units, 250 mesh one unit.A. The outer diameter is 200mm.B. The surface of the steel pipe adopts advanced electroplating chrome process, which is hard, smooth and wear-resistant.C. The dots are consistent and the ink is even.D. Extend the life of plates and rubber rollers.E.The adjustment of the anilox roller gap is adjusted by the self-locking structure , and the adjustment range is 0-12mm.(4) Rubber roller (three group) A. The outer diameter is 195mm.B. The surface of the steel pipe is wrapped with wear-resistant rubber.C. The rubber roller has high special grinding and good ink transfer effect.D. Rubber roller gap adjustment adopts self-locking structure adjustment, the adjustment range is 0-12mm.(5) phase adjustment mechanismA. Planetary gear structure.B. Printing phase adopts electric digital control 360 degree adjustment (can be adjusted both in running and stop.) The adjustment value is more accurate.C.The lateral phase of the printing roller is electric adjusted, and the adjustment range is ±10mm.D. Printing plate roller adopts electric adjustment phase, fast adjustment speed and high precision of adjustment.(6)Feeding paper rollA. The upper paper feeding roller, with an outer diameter of 125mm, is made of high-quality steel hard chrome-plated and equipped with 3 wrenches, and the shaft can be rotated to any position with adjustable paper guide wheels.B. Paper feed lower roller, outer diameter is 155mm, the paper guide roller is plated with hard chrome.C. The adjustment of the paper guide roller gap is adjusted by the self-locking structure , and the adjustment range is 0-10mm.(7) ink circulation structureA. Pneumatic diaphragm pump, stable ink supply, easy operation and maintenance.B. Ink filter to filter impurities.C. Low ink alarm.D. When printing, the rubber rol