Multi-Functional Processor Solvent Based Flexo Plate Processing Machine

Multi-functional Processor Solvent Based Flexo Plate Processing Machine  1. Application Regardless of the PS plate or the CTP plate, a processing machine is required for processing the plate after the exposure is completed. EcooGraphix CTP Processor can be used with Offline/ Online Thermal CTP or CTCP or UV-CTP platesetters, such as Kodak, Screen, Agfa, Creo, Amsky or Cron CTP machines.Model: ECOO FP-900     2. Machine Features ♥  Multi-functional solvent-base flexo plate making machine, allows for exposure, wash-out, drying and de-tacking.♣  AIO design, save space, suitable for small format Flexo CTP Machine.♦  MPU central control panel makes operation easy.♠  Adopt imported UV lamps and electronic ballast.♥  Strong vacuum device and sucking air plate.♣  Circle thermostatic air drying device assures.♦  Accurate and stable re-productivity of the original colors and graphics. 3. Specification Flexo plate processing AIO machine(AIO, All in one model)ModelFP-900Page SizeMax. 920mm*680mmPlate Thickness1.14mm - 3.94mmElectricity RequirementSingle phase 220V 50/60HzWorking Power3.5KWMachine Size(WxLxH)mm1650*1160*1300 4. Caution And Process 1) Do not run the feature of 'water temperature' before you and solvent in the solvent tank.   2) Use three pin leg for the power supply of the machine, the power supply must with the earth connection.   3) Don't open the cover(Figure 1) when washing the resin plate.   4) The power supply is 220V 50-60Hz.   5) Keep it on for 20 minutes after you finished your work.The progress of working:   Adjust the brush   Put the solvent into the solvent tank; and the level of the solvent must lesser than the brush top (0.5-1.0cm). Then wet the brush with solvent and close the cover. Observe the washing flat, if the four sides of the washing flat have the solvent (it means the brush is just touching the solvent), it is suitable for washing. If not, you have to set the height of the brush. There is one fixable screw in four side of the brush, set the height  of the screw to adjust the level of the brush till the brush is just touching the washing flat. (Caution: it is better for you to use the water to replace the solvent to adjust the level of the brush, but you have to put the solvent to the solvent tank till the water is dry, because the water and the solvent are not compatible, it means you have to wait till the water is dry to use the machine).The progress of operation (Figure 2):   First, set the machine in the airy space and check the power supply is working. Press the power (there is a power connection for all section -- 'power', turn it on) to open the machine. Maybe it will wink once because of the power but it is normal.  Set the parameter. Press button 1 to choose up and press the button 5 to choose down (choose the different feature). For example, press the button 5, the light is winking in 'Exposure time', press it again it will wink in 'Wash-out time' and so on. Set the parameter for all functions. When the light is winking, press button 2 and 4 to choose the digit (button 2 is to choose right, button is to choose left). When the digit is winking you can set the parameter. Press button 1 and 5 to add and reduce parameter (button 1 is to add parameter; button 5 is to reduce the parameter). After the setting you have to press button 3 (set) to fix the parameter that you had chosen.   After setting the parameter, you can press every function to run it. When the working time is enough it will stop automatic and voice out few times to show you the working (you can try and check all functions to know it well before you use it).  Exposure function (Figure 1 and 2):   Pull out the function 6 (Exposure section) and roll up the transparent plastic film. Put the film on your resin plate and put it on the flat and press the button 6 (vacuum button) and cover it with the transparent plastic film bit by bit (so that the air will be made out better). (Caution: make sure that your film and the transparent plastic film is clean, no water, no dust no solvent and so on. The resin plate is a little bigger than your film so that the vacuum pump can work better). Observe the window of the vacuum pointer (it is in the right of the machine and it shows the working of pump, the work is good when it is pointing between 0.08 &-0.1)Push the Exposure flat into the machine and press 'Exposure time' and it will work. When it is finished, it will stop and voice out few times to show you the working. Pull out the function 6 (exposure section) again and press button 6 to stop the work of pump. Roll up the transparent plastic film and get the film and resin plate.  Washing and drying (Figure 1 and 2)   Paste the resin plate to the section 2 Washing flat and press the button 'Wash-out time' and close the cover. It will work. You have to watch it out when it is finished(because it is not good for the resin plate and your finished goods if the resin plate is in the solvent longer). The washing time is 3-6 minutes