High Quality Medical Waste Industrial Waste Solid Waste Hazardous Waste Management Rotary Kiln Incinerator Professional Factory

Scope of application: Viscera cut by medical bistoury, medical auxiliary material, one-time injector and other medical garbage. Characteristics:1. Automatically fill the material, and automatically output the ash;2. Without any smoke, smell or second public pollution, dry and low burning and running cost;3. Incinerator body adopts the revolving type. Mill and multiple-phase burning have good burning effect;4. Cremate inside out, less ash, and heat alkali burning rate is over 90%;5. Continually fill the material, every kind of garbage with high water containing rate and a little water could be plunged in to burn together.6. Advanced automatic control technology ensures safe and reliable operation of equipment, low operating cost and remarkable economic benefits.7. High efficiency: without any smoke,any smell or second public pollution;8. Save energy: science leading structure, the treatment is more complete, and running cost is lower;9. Safe and reliable: mainly adopt automatic controlling System with olw malfunction rate, convenient repair and maintenance;10. Exhaust  reaches national standard: have high-efficiency tail gas disposal device such as  secondary combustion chamber, heat exchange, dust removal and so on. Its tail gas could accord with national newest exhaust standard.Hazardous waste handling capacity:50-5000kg/hSafety indicators1. The burner of the incinerator is equipped with a safety protection device, which will automatically cut off the fuel supply when the burner starts abnormally.2. Before the incinerator stops running, there is a combustion chamber cooling program (normal shutdown and safety program shutdown). When the temperature drops to the set value, the cooling program ends and the incinerator stops working.3. The equipment is equipped with leakage protection device. When the temperature is 40 degrees and the relative humidity is 85%, the insulation resistance of the electrical circuit is greater than 2 MΩ, and it can withstand the experimental voltage of 1min power frequency (50Hz) and 1500V. The positioning of each part is accurate and the connection is reliable.4. Oil, water and gas paths have been sealed pressure test, no leakage phenomenon.5. Alarm system:1) Power indicator and switch of incinerator device;2) Residual burning timing device is to ensure no residual flammable gas and organic matter in the furnace. The operation is safe and reliable ;3) Overload protection device to protect the motor from overload, negative pressure frequency conversion control;4) High and low temperature control interlocking.  Design ideas:According to the characteristics of the project, the rotary kiln incinerator is selected, which can burn solid and liquid at the same time. Especially for chemical residue, sludge, organic waste liquid, industrial solid waste, etc.,it is the preferred furnace type for comprehensive waste disposal center. Rotary kiln incinerator is built in a cylindrical metal shell insulation brick, horizontal slightly inclined, through the overall rotation of the furnace body to achieve uniform mixing and move to the discharge end along the inclined Angle. This incinerator adopts flue gas directional design. Through the rotation of the furnace body, the waste is constantly rolling and stirring to ensure the uniformity of heating, and the residence time of the waste in the rotary kiln can reach 0.5-1 hours, which can ensure that the waste is fully heated and the organic matter is fully removed. At the same time, it equips with a second combustion chamber and the waste gas generated by the rotary kiln incinerator is again incinerated at high temperature (1100ºC) to ensure the removal efficiency of organic matter. According to the use of temperature ≥1100ºC and flue gas residence time ≥2 seconds selects furnace type. After flue gas cooling, the tail gas is mainly purified, mainly from the removal of acidic components and nitrogen oxides, adsorption of harmful components and dust particle collection for equipment selection. Incinerator device includes the following equipment:Feed hydraulic transmission device, waste liquid conveying pipeline system, rotary kiln body, the primary burner, the secondary combustion chamber, the secondary burner, water cooled cyclone dust removal, quench acid stripping tower, mist separation tower, exhaust fan, independent chimney, alkali storage tank and conveying system, lye pump, blower and air supplying system, electrical system, instrument control system, automatic ash device, system installation and maintenance's platform and support, etc.Brief introduction of main process flow:1) First, open the blower and purge the residual gas and other flammable and explosive gases in the furnace to prevent explosion after ignition.2) Before ignited by the burner, please open the induced draft fan first and purge the furnace for five minutes. The fuel diesel is transported through pipelines and ignited by ignition burners. The heat release from the burner incr