High Pressure Oil Free Oxygen Compressor with 3 Stages

  Product DescriptionHIGH PRESSURE OIL FREE OXYGEN COMPRESSOR Sr.ProgramParameters1Compressed mediumOxygen (must be dry and particle-free gas)2Rated flow (standard state)  (Nm3/h)303Intake air temperature  (ºC)≤404Inlet pressure  (MPa)0.45Exhaust pressure (MPa)206outlet pressure/Temperature200kg/50ºC7Bore * Quantity (mm)Φ90+φ50+φ308Rotating speed  (r/min)4709Cooling wayAir cooling + water cooling (with self-circulation)10Lubrication wayOil free lubrication11Compression stages3stages12Structure typeAngle type, W type, single unit13MotorPower (kW) 15Electric system AC380V,Three-phase,50Hz,Insulation classLevel BProtection levelIP44Start methodDirect start14Transfer methodBelt drive15Installation typeBasic type16Nois  ( dB(A))≤8017Control wayPLC touch screen control: maintenance alarm, over temperature alarm, over pressure alarm, motor overload alarm, water cooling alarm18Import and export sizeRc1/2   Rc5/819Dimensions(L×W×H)/ mm1350*1000*115020Weight / kg≈450Working principle and technical parameters1,Working principle 1.1 The compressor belongs to reciprocating, piston (with middle body and cross head), single acting, combination of air cooling and water cooling, three-stage compression, all oil-free and lubricated oxygen canned compressor (hereinafter referred to as the compressor).1.2 The compressor is composed of the main engine, the motor, the support and the electrical control elements. The main engine and the motor are placed on the support. It is equipped with a one-way valve, an inlet ball valve, an exhaust globe valve, a cooling water pump and a flow meter, and a solenoid valve is installed in the inlet pipe and the unloading pipeline.1.3 When the compressor is working, the motor drives the crankshaft to produce rotary motion through the v-belt, and the piston produces reciprocating motion through the connecting rod, which changes the cylinder volume and leads to the change of gas pressure in the cylinder. The gas in the pressure state is inhaled into the cylinder through the inlet valve block, the inlet solenoid valve, the inlet pipe and the inlet valve. The compressed gas is compressed into the required pressure through three stages and discharged through the one-way valve, pipeline and exhaust valve block for use.1.4 It is provided with inter cooler between the first, second and second and third stages.2,This product is suitable for:The compression medium is dry non-granular oxygen pressurization or tank.3,Basic technical parameters (see P6 -- table 1).Control systemThe control system of the compressor is composed of YKHMI touch screen, PLC controller, pressure sensor (inlet and supply pressure), temperature sensor (first stage temperature, final stage temperature), inlet solenoid valve, unloading solenoid valve, one-way valve and pipeline. The volume flow rate of the compressor should be able to adapt to the change of the volume of air used. When the volume of air used is less than the volume flow rate of the compressor, the volume flow rate should be adjusted by the control system to prevent the continuous rise of the supply pressure. Display pressure and temperature in real time while working.When the inlet pressure reaches 0.4mpa, press "start up", and the compressor starts to work according to the starting control sequence of When the exhaust pressure reaches the set value of 15MPa, the motor power will be cut off automatically and the compressor will stop working. At this time, the intake electromagnetic valve is closed, the air inlet is closed, and the unloading solenoid valve is opened, so that the high-pressure cavity and pipeline of the exhaust end are connected with the air inlet and the air inlet, so as to reach the same pressure on both sides. At the same time, the cooling pump stops working, so as to realize no-load starting.Packaging & Shipping Certifications   FAQ1:How can I choose the most suitable product ?A: Please tell me your specifications ,we can choose the best model for you , or you can choose the exact model .You can also send us the products drawing ,we will choose the most suitable product for you . 2: Can you produce according to the sample ?A: Yes,we can produce according to the samples or technical drawings provided by customers.3: What is your sample policy?A:If we have off-the-shelf parts, we can provide samples, but the customer has to pay for the sample cost and the Courier fee.4: Do you accept OEM order?A: Yes, we can accept OEM order with your own logo as per your requirement if quantity reached. Please ask for details. 5: What is your trade terms?A : EXW,FOB, CFR and CIF all acceptable. 6: What's the Payment Terms ?A : T/T, L/C,D/P,D/A 7: What's the MOQ?A: 1 set .(Only some low cost product will be more than 1 set )8: How do you maintain a good long-term relationship?A:1.We provide our customers with excellent quality and competitive price.Ensure customers have an advantage in the market competition.2. Always implement and implement the cooperation concept of