Silenced Diesel Pumpset station JQS : The silenced
diesel engine pump, developed with advanced technologies, is used
for emergency fire control and living water supply. With large
flow and high lift, it is suitable for long-distance water delivery
with the large flow. It has higher efficiency with a double
channel design. Equipped with a vacuum-assisted system, it can
achieve self-suction without irrigation. Characteristics:1. 1m
noise measured 65dB(A)-85dB(A);2. Silenced diesel engine pump, has
a compact structure, small;3. The vibration absorbed, to reduce
vibration and noise;4. Noise absorbed material-made cover, to
reduce noise;5. Noise absorbed compound silencer reduces noise;6.
High-efficient noise-off inlet channel;7. Big-capacity fuel tank;8.
Cap plate, easy to maintain.Conditions:1. Altitude:≤2500m2. Ambient
temperature:-25~55ºC3. Relative humidity:9~95%4. Earthquake: 7
degree5. Flow range: 50-700(L/S)6. Head range: 32-600m7. Diesel
engine power: 18-1100KW8. Media part materials: cast iron, graphite
cast iron, stainless steel, cast copper.Silenced diesel engine
pump:1. automatic start: when receiving fire/piping network/power
off/other start signals, in 5s, automatic start with a full load;2.
automatic charging: the storage can carry out automatic charging by
industrial power supply or diesel charging motor;3. automatic
warning: automatic warning for diesel engine low oil pressure, high
water temperature, ultra-speed;4. automatic preheat: for
emergency;5. Direct coupling: under 360kw, diesel engine pump,
innovative, flexible shaft couples, direct coupling.Technical
Parameter : Flow80 - 3600 m3/h Head 10 - 210
m Speed 980 - 3000 RPM Power11 - 1600
kWCaliber 150 - 600
mm Start, running and stop Start1. First of all, pour water into pipes, to make the pump and inlet pipe filled with water. The pipes shall be sealed, no air leaked. (no-water inside start is forbidden) 2. Close globe valve and cock on outlet pipe, to reduce start currency.3. Rotate the rotor by hand, lubricate the bearing and check
the pump impeller, seal the
ring, if it cannot rotate, you shall not start.4. Try to start, motor rotation direction shall be as same as the arrow direction on the pump. 5. When
the
rotor works normally, open gradually the outlet globe valve, adjust for the work conditions required.Running1. Observe the reading in meters, keep it running around the flow and head shown on the nameplate.2. Regularly check, motor currency value shall not exceed rated currency value.3. Pump bearing temperature shall not exceed 75ºC, and shall not be 35ºC higher than ambient environment.4. To start, loosen
the
stuff cap. Adjust later when started.5. In case
of
fragile component abrasion, replace in time.6. When any abnormal happens, immediately stop and check.Stop1. Close the globe valve on
the outlet pipe, close the
vacuum gauge cock.2. Stop the
motor, and close the
pressure cock.3. In Winter, drain the
liquid in the pump completely to avoid frozen cracks.4. When you will not use it for a long time, uninstall the pump, clean,
and lubricate Troubleshooting FaultCauseSolutionThe
pump
cannot suck water, pressure gauge & vacuum gauge vibrating 1. Insufficient water pouring 2. Leak between pipe and meter 3. Suction is too high 1, check
a leak in the
bottom valve. 2, Tighten the leaked part 3, reduce suction The
pump cannot suck, high vacuum is shown in the
vacuum gauge1, bottom valve closed or jammed 2, Too great water suction resistance 3, filter jammed 1, check bottom valve2, replace water suction pipe3, clear off
the
filterPressure gauge works, no water outcome1. Great outlet water pipe resistance2. Wrong rotation direction 3. Outlet pipe valve closed4. impeller jammed 1. check or shorten water pipe 2, check
the motor, adjust 3, open the
valve and clear off the
impellerCannot reach designed flow1. air sucked 2. Water level drops, submerged depth is not enough 3. impeller jammed 4. rotor torn and worn 1, check leak part and clear off 2, prolong water inlet pipe, increase
the
submerged depth3, uninstall and clear off 4, replace seal ring Great pump power consumption1. Stuff tightened, overheated 2. Great flow 3. Collision between rotor and case 4. Pump shaft bearing abrasion 5. Pump shaft misplaced1. loosen slightly2. reduce globe valve opening3. adjust 4. replace bearing 5. replace or adjust Great pump vibration 1. impeller partially jammed 2. impeller damaged 3. little flow 4. non-concentric between pump shaft and motor.5, bearing damaged 6, gas etching1. Uninstall and clear off 2, replace 3, increase opening 4, adjust5, replace 6, change suction inlet position Borra
Technology Co., Ltd.Borra Technology co., Ltd., founded in 1995,
owns a top-rank design, production, sales, and service team, and
modern production lines, to manufacture various self-priming pumps,
movable diesel pumps, diesel Self-Priming dirt drain pumps, diesel
fire pumps units, diesel mini pumps Certificate
: Services:1. One year or 1000 working hours guara
Related products about Silenced Diesel Pumpset Station.
- Waste Tyre Plastic Recycling Machinery Machine Tire Crusher Production Line Rubber Crumb Grinding Machine Equipment Tire Shredder
- Stretch Plastic Blowing Pet Bottle Making Blow Molding Machine Bottles Stretch Automatic Pet Bottle Blowing Machine
- Waste Plastic Pet Bottle, Water Bottle Flake, PP/HDPE/LDPE PE Film Jumbo Woven Bags Plastic Crusher Machine, Plastic Crushing Washing Recycling Machine
- Type 2 Wall-Mounted Electric Car Charging Station 7kw /11 Kwelectric Vehicle Charging Station Home Wallbox AC EV Charger Single Phase or 3three Phase
- G-View G12W Wholesale Auto Car LED Headlight Bulb High Power H13 H11 9005 H7 H4 Car LED Headlights LED Car Lights
- New Design Porcelain Round Plates Dinner Set for Wedding and Banquet
- China 2023 New Design Super Soft 100% Polyester Microfiber Knitted Oversized Decoration Hoodie Blanket
- Handmade Art Creative Materials Thickened White Paper Cup DIY Disposable Handmade Colored Paper Cup