Okyla Small Petrol White Black Red Gsoline Engine 6.5HP 7.5HP 13HP

  Product Description  Our main products are Gasoline Engine, Diesel Engine, Gasoline Generator, Diesel Generator, Water Pumps and Pressure Washer etc. Our products have been exported to more than 50 countries and areas. Our main markets are in Europe, north America, south America, Africa, Middle East and Southeast Asia area etc. Vision: Become the machinery company with the most reliable quality, the most professional technology, the most diverse products, and the best service. All specifications can be discussed in detail, including sample price, MOQ, product price, shipping method, payment method etc.Product ParametersModelOK160   OK160EOK200    OK200EOK210    OK210EEngine typeOHV Single-cylinder,4-stroke,Air-cooled Gasoline EngineBore*Stroke68*4568*5470*55Displacement(ml)163196215Compression ratio8:05:01Max.output(HP/rpm)5.5/36006.5/36007.5/3600Max. torque(N.M/rpm)10.8/250013/250015/2500Fuel tank capacity(L)3.6Engine oil capacity(L)0.6Dimensions(L*W*H)(mm)415*340*385415*340*385415*340*385Net weight(KG)13Detailed PhotosThe difference between 168F and 168FE:Manual or electric   Packaging & Shipping We will ship according to the order quantity of goods and the demands of customers. Company Profile     FAQ1.Q: Are you a factory or trading company?We are a factory with three large plants and we are the leading enterprise in the agricultural machinery industry. 2.Q: Why should you buy from us, not from other suppliers?Over the years, we have been focusing on the manufacture of advanced electrical and mechanical products. With the goal to manufacture high-quality products. 3. Q: Whether you could make our brand on your products?Yes. We can print your Logo on both the products and the packages if you can meet our MOQ. 4.Q: Whether you could make your products in our color?Yes. The color of products can be customized if you can meet our MOQ. 5. Q: How to guarantee the quality of your products?1) Always a pre-production sample before mass production. 2) Strict sampling inspection on products before shipment and intact product packaging ensured. Installation Instructionspower end maintenance1, must be checked before operation, control level. Plunger pump first run 50 hours, replace the lubricating oil must, after the replacement once every 200 hours.2, all the screws must be tightened3, the pump during operation, the lubricating oil temperature should not exceed 70 ° C, the medium temperature of not more than 55 ° C4, the Shell grade lubricants can withstand S2G > 205, note the lubricating oil must be injected from the injection hole (remove vent cap is the oil hole), lubricating oil injection volume of approx. 18 litres6, oil injection, must be approved by the 80 - 100 to the filter net, filter implantation. To prevent the impurities in the crankcase oil injection in vivo7, observe the oil pump operation condition, the oil pressure of lubricating oil is maintained at 0.1 - 0.15MPa, oil can be observed from the transparent hose, oil of HERSHEY'S yellow transparent oily, poor gray opaque, black oil difference, under normal circumstances is black when it should be replaced8,the lubrication system, the filter should be cleaned at any time over the network, if the filter oil filter must be damaged replacement9, the replacement of lubricants, must be carried out in the hot state, the old oil on the net, at least once a year the old oil vent, crankshaft box must be clean to add new oilBefore 10, every oil change, should first check whether the water inlet part and resolved after the injection of new oil. Check the position of the middle rod: seals, seal, piston fillersThe connecting rod bolts in 11, always pay attention to the part of the pump connections, prevent faultsthe fluid end maintenance1, the suction and exclusion side screw2, the packing box should be promptly replaced leakage seal3, the protection of the plunger includes shall not be affected by any damage using piston cylinder. When not coated with anti rust oil protection screws from damage4, pump head should be cleaned regularly suction filter;5, work longer should adjust the sealing ring, check the valve seat on the check valve, spring is worn, replace if necessary6, use special tool screwing the locking nut, is closely connected to check the piston and the middle rod, must pay close attention toSeal 7, leakage should be replaced8, the pump should be installed horizontally, before installation should be carefully check all parts, below the intact condition can be installed  /* March 10, 2023 17:59:20 */!function(){function s(e,r){var a,o={};try{e&&e.split(",").forEach(function(e,t){e&&(a=e.match(/(.*?):(.*)$/))&&1