3213-800 RO Membrane Price for Water Treatment System

Product DescriptionProduct Name: 3213-800 RO Membrane Price for Water Treatment SystemProduct ParametersSeriesModelActive areaSalt rejectionWater outputTest prssureFt2(m2)%GPDPSI15101510-502(0.17)9750651510-753(0.25)977565ECO1812-50 9L3.5(0.35)9750651812-75 9L3.5(0.35)977565238mm1812-50 13L4(0.4)9750651812-75 13L4(0.4)9775652012-100 13L5(0.5)97100654000ppm1812-754(0.4)95751202012-804.5(0.45)96801202012-1005(0.5)96.5100120Regular1812/20122000ppm1812-50 11L4(0.4)9750651812-75 11L4(0.4)9775652012-80 12L4.5(0.45)9780652012-100 13L5(0.5)97100652012-125 13L5.2(0.52)97125652012-1506(0.6)97150652012-18010(1.0)97180652012-2007.5(0.7)9720065SeriesModelActive areaSalt rejectionWater outputTest prssureFt2(m2)%GPDPSI30123012-2008.6(0.8)97200653012-25010.8(1)97250653012-30013(1.2)97300653012-40015(1.4)97400803012-60020.5(1.9)966009030133013-40015(1.4)97400803013-50018.3(1.7)96500803013-60020.5(1.9)966009032133213-60020.5(1.9)96600903213-80026(2.5)968009034133413-80028(26)96800903413-100032(3)95100090Inline RO1812-754(0.4)9750/75/10065Packaging & Shipping25PCS/CTN, 32*32*34CM, 7KGS/CTNInstallation InstructionsInstallation InstructionsUnscrew the nut on the membrane shell cover at the inlet water connection end, take out the inlet water pipe, then use the membrane shell wrench to loose the membrane shell cover. Take the RO membrane from its packaging, put the end of the membrane with 2 O-rings into the RO membrane shell (See The following Diagram ) and push it in, finally screw the membrane shell cover back on, and tighten it with membrane shell wrench, put the inlet water pipe back into the inlet water connector and screw the nut tightly, then push the membrane shell card into the large single clip. Direction For Use1. When installing the RO membrane, you should pay attention to the direction of the membrane;2. When installing the RO membrane, you should first make sure that one end of the membrane has 2 O-rings;3. When installing, be sure to put the end with the O-ring into the end of the membrane shell with the pure water connection, for correct installation you need only a little force to put the RO membrane into the membrane shell, if you encounter too much resistance, please do not force the membrane into the shell, or it could lead to permanent damage to the membrane shell or membrane components (the membrane manufacturer does not take the responsibility for replacing components due to damage made during installation);4. Damage to the membrane shell and membrane element caused under above mentioned situation is not covered by the warranty.Company ProfileOur AdvantagesA. Full range RO membranes 50GPD to 1000GPD for home use.B. Self-produced membrane sheet.C. Each roll of membrane sheet will be tested before bulk production.D. Each finished membrane will need pass vacuum testing, to make sure salt rejection rate.E. OEM and ODM orders are welcomed.FAQFAQs on Reverse Osmosis RO membrane OEM manufacturingQ1: What type of RO membrane is avaliable in your company?A1: In general, Hikins has Domestic RO membrane and Industrial RO membrane, For Domestic RO membrane, Hikins has Municipal Tap water RO membrane, Rural Area Under Ground water RO membrane, High-flow Low pressure RO membrane, and Brackish water RO membrane. For Industrial RO membrane, Hikins has Low Pressure Engergy saving RO membrane, BW Brackish water desalination RO membrane, FR Fouling Resistant RO membrane, as well as XLE Extreme Low Pressure RO membrane, and High Salinity Brackish Water Desalination RO membrane. Q2: What is Salt Rejection Ratio?A2: The Salt rejection describes the quality of salt removed from the Reverse Osmosis feed water stream as a percentage. It's one of the key element of the RO membrane quality, however, other essential elements such as RO membrane performance durability, stability, application scope in different region, and permeate flow output at the same pressure will all be the important factors to judge the quality of the membrane. Q3: Is the Salt reation of the RO membrane the higher the better?A3: This will be depending on the feed water quality, if the feed water quality is good, even a 90% salt rejection membrane will be workable, if the feed water is with bad quality and with brackish water environment, a higher salt rejection above 95% is an ideal choice. For any membrane that meet the local drinking water standard will be a good membrane. Q4: Is there are any other element we need to take into consideration when selection the RO membrane?A4: Yes, the pre-treatment filter cartridge and pre-treatment system will affect the RO membrane performance as well, please select good quality filters and pre-treatment system. Q5: Why there are white foam-like water being in the treated water at the initial usage?A5: To preserve the RO membrane for a long shelf-life, and prevent the membrane from being oxydized, a water soluble protection material is coated on the surface of the membrane, which will be rejected in both the rejected water