30 Meters Remote Control Distance Door Opener for Garage Door

Product DescriptionProduct DescriptionSDM-10G32/SDM-20G32 Encryption Sliding Gate Motor General Introduction:In order to make the installation and configuration easier, we have developed this intelligent one button learning sliding door control board. The control board adopts advanced microcomputer chip, digital control, more practical functions, higher safety performance, easier installation and configuration. Fully compatible with the smartphone app network (WiFi/3G/4G/5G) control and bluetooth control and many other features.Features:1. Anti-rush design. At the first operation after each power on, the motor runs in slow motion to the limit point throughout the process to avoid rushing out of the limit. When the door reaches the limit point, the motor can only be operated by pressing the button of the opposite direction to prevent the limit from being broken out. (Notice: It has the power off protection function when in place, and the motor only moves in the opposite direction when repowered).2. Master-slave mode available. Two motors with the same control board on each can work synchronously. In this mode, infrared, ground sense, automatic door close and other functions are synchronized. Attention:Infrared, ground sense must be connected to the master motor.3. Motor runtime protection. To prevent the motor from running during the travel failure, the control board will automatically learn the motor running time without manual setting, and 10s will be added automatically as the time margin.4. Auto-close function. Time can be set from 1s to 250s before the door closes automatically. The default value is 3s.5. Soft start and slow stop. There're soft start and slow stop features available. The distance and speed of the slow stop feature can be adjusted.6. Stop & rebound against resistance. Switchable between stop against resistance and rebound against resistance for the closing travel. Stop against resistance for the opening travle.7. Onboard socket for bluetooth module. A socket is integrated onboard for the insertion of the standalone bluetooth module (module not included by default).8. One button configuration for internet control. Can be directly paired with the internet controllers through pressing one button onboard, no copy procedure is required.Product Parameters:Working voltageDC24V outputMax output current10AFuseAC220 20ARemote Distance30mRemote control2pcs anti-copy rolling code remotesWorking temp-25ºC to +75ºCMax gate weight1000kgOutput Torque21N.mRotation Speed12m/minLimit SwitchMagnetic(NC/NO) SpringNoiseless than 50dBMobile APPwith WIFI or BluetoothCharger power battery24V3A charger power battery(not include)Encryption Remote Frequency433MHZDiagram:Configuration Introduction:Dip Switch : Remote Control One-key and Four-key Modes SwitchOFF position: Remote control with four independent keys functioning as Open, Close, Stop, Lock.When in the non-passageway mode, after pressing the Lock key, the Stop key needs to be pressed in prior to being able to operate.ON position:(1) A single key on the remote is the one-key control key (The specific key pressed while pairing).(2) Each key on the remote is a one-key control key.Function setting: Turn and only turn and to ON, press SET once with a buzzer is the single key one-key mode, press again with 4 buzzers is the 4 keys one-key mode. Turn to OFF after setting.Dip Switch : Passageway ModeOFF Position: Enable the Lock button on the remote. (Refer to Remote Control Pairing on Page 4)ON Position: Enable the passageway mode ( at OFF, at ON).When the gate is closed at the limit position, press the Lock key will make the motor run in the opening motion for 6s.Dip Switch : Auto-closeOFF Position: Disable the auto-close function.ON Position: Enable the auto-close funciton. Only when the gate is opened at the limit position will the countdown starts, then the gate will automatically close to the limit position.Auto-close timer setting: Turn and only turn and to ON, each press on the SET key is 1s, set it as long as you wish up to 250s. After setting, turn to OFF.Dip Switch : Slow StopOFF Position: Disable the slow stop function.ON Position: Enable the slow stop function (Effective only after travel distance learning).The speed of Slow Stop can be adjusted with the MT adjustor, turn it clockwise to gain the speed, turn it anti-clockwise to reduce the speed.Travel Distance Learning: Turn and only turn and to ON, then hold down the ONE key until the gate starts running auomatically and release. It will close to the limit and open to the limit, and close to the limit again with the slow stop effect. After 2 beeps, the travel distance learning procedure is complete.Dip Switch : Startup StrengthOFF Position: Enable the slow start function. The gate runs at a slower speed for the first 2s, to reduce the tremble of the gate.ON Position: Max start speed. The gate runs at the maximum speed from the very beginning.Dip Switch : Setting KeyOFF Position: Make the settings tak