Engine Oil Dipstick Indicator Oil Level Gauge for Fiesta 1.6L 2011-2017 Be8z6750b

NotesYearMakeModelTrimEngine 2016FordFiestaSE Hatchback 4-Door1.6L 1596CC 97Cu. In. l4 GAS DOHC Naturally Aspirated 2016FordFiestaSE Sedan 4-Door1.6L 1596CC 97Cu. In. l4 GAS DOHC Naturally Aspirated 2016FordFiestaS Hatchback 4-Door1.6L 1596CC 97Cu. In. l4 GAS DOHC Naturally Aspirated 2016FordFiestaS Sedan 4-Door1.6L 1596CC 97Cu. In. l4 GAS DOHC Naturally Aspirated 2016FordFiestaTitanium Hatchback 4-Door1.6L 1596CC 97Cu. In. l4 GAS DOHC Naturally Aspirated 2016FordFiestaTitanium Sedan 4-Door1.6L 1596CC 97Cu. In. l4 GAS DOHC Naturally Aspirated 2015FordFiestaSE Hatchback 4-Door1.6L 1596CC 97Cu. In. l4 GAS DOHC Naturally Aspirated 2015FordFiestaSE Sedan 4-Door1.6L 1596CC 97Cu. In. l4 GAS DOHC Naturally Aspirated 2015FordFiestaS Hatchback 4-Door1.6L 1596CC 97Cu. In. l4 GAS DOHC Naturally Aspirated 2015FordFiestaS Sedan 4-Door1.6L 1596CC 97Cu. In. l4 GAS DOHC Naturally Aspirated 2015FordFiestaTitanium Hatchback 4-Door1.6L 1596CC 97Cu. In. l4 GAS DOHC Naturally Aspirated 2015FordFiestaTitanium Sedan 4-Door1.6L 1596CC 97Cu. In. l4 GAS DOHC Naturally Aspirated 2014FordFiestaSE Hatchback 4-Door1.6L 1596CC 97Cu. In. l4 GAS DOHC Naturally Aspirated 2014FordFiestaSE Hatchback 4-Door1.6L 1597CC 98Cu. In. l4 GAS SOHC Naturally Aspirated 2014FordFiestaSE Sedan 4-Door1.6L 1596CC 97Cu. In. l4 GAS DOHC Naturally Aspirated 2014FordFiestaSE Sedan 4-Door1.6L 1597CC 98Cu. In. l4 GAS SOHC Naturally Aspirated 2014FordFiestaS Hatchback 4-Door1.6L 1596CC 97Cu. In. l4 GAS DOHC Naturally Aspirated 2014FordFiestaS Hatchback 4-Door1.6L 1597CC 98Cu. In. l4 GAS SOHC Naturally Aspirated 2014FordFiestaS Sedan 4-Door1.6L 1596CC 97Cu. In. l4 GAS DOHC Naturally Aspirated 2014FordFiestaS Sedan 4-Door1.6L 1597CC 98Cu. In. l4 GAS SOHC Naturally Aspirated  PRODUCT SPECIFICATIONSPart #Be8z6750bSKU #Be8z6750bWeight0.25lbsLocation:Engine Oil DipstickMaterialSteelProduction description We were supply the pipe for a lot of application such as auto engine cooling system and the others ,We also support the after market service.MOQ is also ok for us  Quality control 1.Each part go go though air decay leak test  1Bar@0.5CC/Min  2.Copper braze paste CU 103-BS EN ISO 17672 3.Part ship to plant or service part package free of any corrosion aligned with the Ford customer service 4.Part clean conform to ES7T4E-6B616-AA,cleanliness extraction efficiency requirement is 60% Min. 5.Tube steel EN10305-3 E220 CR2 S3 6.Bracket steel 3.0THK SAE J403 UNS G10080 OR G10100 0.2% C MIN Customer first:We control the quality by APQP,PPAPCONCEPT:Why does it always seem that we have plenty of time to fix our problems once they occur, but never enough time to prevent the problems from happening by doing it right the first time? That was why we PFEMA and HISTORY LEARNING first for all the project.Thanks to our customer the recourse we were standing here todayWe focus on the stamping forming bending welding part for almost 30 years.Founded in 1992, Started exporting in 2008, which is now covered more than 10000 square meters and with 439 employee.We fully carry out the TS 16949 quanlity management system with manufactory.Start from raw material incoming inspection to container loading . Continuous improvemnet:ACT-PLAN-DO -CHECK Raw material incoming inspection :Raw material incoming inspection :1.Five element analyzerAutomatic five element analyzer carbon sulfur manganese silicon phosphorus chemical element spectrum analyzerAny type of the element out of specification will Affecting mechanical propertiesRaw material incoming inspection : 2.Mechanical PropertiesOnly tensile strength, yield strength and elongation of raw materials meet the requirements can move into mass productions.DecoilerWe bought the raw material by coil from the steel company ,we decoiler the steel sheet by ourslef ,which will save the cost and lead time for mass productions.Laser cutting for the steel sheet When produce the sample or the small batch of the product we normally use the laser cutting insted of the stamping blanking.Tooling mold PrepareWe simulated the workpiece by J-STAMPING software ,then we design the mold for metal sheet part ,not only it short the leadtime for development but also saving the cost for customer.Mold Workshop WarehouseWe can design and manufacture molds according to customer requirements,2500 square meter special for stamping mold warehouse.CNC machining centerWe introduce 5pcs of CNC machine ,all of them with 5 Axis not only they can produce the mold and tooling but also they can carry out some part of machine job. The capacity of the CNC machine was :25000*1800*1000mmStamping WorkshopOverview of the Stamping workshop with cover the Stamping equipment from 100T to 800T. Hydraulic Press cover from 50T to 3100T. With the mold(die,tooling) produce by ourselves we can customize all kinds of metal shape according to customer drawing call out. Metal sheet bending by machine without mold or tooling help by press or stamping machineBending WorkshopCNC bending machine with servo co